[Gluster-users] Gluster and bonding

[Vincent Royer]

I do what you're trying to do, with bonds going to two independent switches
(not stacked) from each host.

Works fine for the engine, vms network, migration, etc, but I don't use
Gluster.  Either cable can be pulled or either switch rebooted without
disturbing Ovirt.  Switches are connected to each other as you've
described.

I'd like to get to the bottom of why it's not working with Gluster, because
I plan the same as you.

On Tue, Feb 26, 2019, 6:15 AM Alex K <rightkicktech at gmail.com> wrote:

>
> Thank you to all for your suggestions.
>
> I came here since only gluster was having issues to start. Ping and other
> networking services were showing everything fine, so I guess there is sth
> at gluster that does not like what I tried to do.
> Unfortunately I have this system in production and I cannot experiment. It
> was a customer request to add redundancy to the switch and I went with what
> I assumed would work.
> I guess I have to have the switches stacked, but the current ones do not
> support this. They are just simple managed switches.
>
> Multiple IPs per peers could be a solution.
> I will search a little more and in case I have sth I will get back.
>
> On Tue, Feb 26, 2019 at 6:52 AM Strahil <hunter86_bg at yahoo.com> wrote:
>
>> Hi Alex,
>>
>> As per the following ( ttps://
>> community.cisco.com/t5/switching/lacp-load-balancing-in-2-switches-part-of-3750-stack-switch/td-p/2268111
>> ) your switches need to be stacked in order to support lacp with your setup.
>> Yet, I'm not sure if balance-alb will work with 2 separate switches -
>> maybe some special configuration is needed ?!?
>> As far as I know gluster can have multiple IPs matched to a single peer,
>> but I'm not sure if having 2 separate networks will be used as
>> active-backup or active-active.
>>
>> Someone more experienced should jump in.
>>
>> Best Regards,
>> Strahil Nikolov
>> On Feb 25, 2019 12:43, Alex K <rightkicktech at gmail.com> wrote:
>>
>> Hi All,
>>
>> I was asking if it is possible to have the two separate cables connected
>> to two different physical switched. When trying mode6 or mode1 in this
>> setup gluster was refusing to start the volumes, giving me "transport
>> endpoint is not connected".
>>
>> server1: cable1 ---------------- switch1 --------------------- server2:
>> cable1
>>                                             |
>> server1: cable2 ---------------- switch2 --------------------- server2:
>> cable2
>>
>> Both switches are connected with each other also. This is done to achieve
>> redundancy for the switches.
>> When disconnecting cable2 from both servers, then gluster was happy.
>> What could be the problem?
>>
>> Thanx,
>> Alex
>>
>>
>> On Mon, Feb 25, 2019 at 11:32 AM Jorick Astrego <jorick at netbulae.eu>
>> wrote:
>>
>> Hi,
>>
>> We use bonding mode 6 (balance-alb) for GlusterFS traffic
>>
>>
>> <https://access.redhat.com/documentation/en-us/red_hat_gluster_storage/3.4/html/administration_guide/network4>
>> https://access.redhat.com/documentation/en-us/red_hat_gluster_storage/3.4/html/administration_guide/network4
>>
>> Preferred bonding mode for Red Hat Gluster Storage client is mode 6
>> (balance-alb), this allows client to transmit writes in parallel on
>> separate NICs much of the time.
>>
>> Regards,
>>
>> Jorick Astrego
>> On 2/25/19 5:41 AM, Dmitry Melekhov wrote:
>>
>> 23.02.2019 19:54, Alex K пишет:
>>
>> Hi all,
>>
>> I have a replica 3 setup where each server was configured with a dual
>> interfaces in mode 6 bonding. All cables were connected to one common
>> network switch.
>>
>> To add redundancy to the switch, and avoid being a single point of
>> failure, I connected each second cable of each server to a second switch.
>> This turned out to not function as gluster was refusing to start the volume
>> logging "transport endpoint is disconnected" although all nodes were able
>> to reach each other (ping) in the storage network. I switched the mode to
>> mode 1 (active/passive) and initially it worked but following a reboot of
>> all cluster same issue appeared. Gluster is not starting the volumes.
>>
>> Isn't active/passive supposed to work like that? Can one have such
>> redundant network setup or are there any other recommended approaches?
>>
>>
>> Yes, we use lacp, I guess this is mode 4 ( we use teamd ), it is, no
>> doubt, best way.
>>
>>
>> Thanx,
>> Alex
>>
>> _______________________________________________
>> Gluster-users mailing listGluster-users at gluster.org <https://lists.gluster.org/mailman/listinfo/gluster-users>https://lists.gluster.org/mailman/listinfo/gluster-users
>>
>>
>>
>> _______________________________________________
> Gluster-users mailing list
> Gluster-users at gluster.org
> https://lists.gluster.org/mailman/listinfo/gluster-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.gluster.org/pipermail/gluster-users/attachments/20190226/ece0b64b/attachment.html>